年年有"余"

 找回密码
 立即注册

QQ登录

只需一步,快速开始

查看: 2809|回复: 0

思科网络学院 CCNA2 ERouting Chapter 2

[复制链接]
  • TA的每日心情
    奋斗
    2022-12-13 21:26
  • 签到天数: 371 天

    [LV.9]以坛为家II

    发表于 2014-10-11 22:14:20 | 显示全部楼层 |阅读模式
    本帖最后由 Sian 于 2015-7-17 15:31 编辑

    Which of the following is true regarding CDP and the graphic shown?

    CDP running on Router D will gather information about routers A, B, C, and E.
    By default, Router A will receive CDP advertisements from routers B and C.
    If routers D and E are running different routing protocols, they will not exchange CDP
    information.
    Router E can use CDP to identify the IOS running on Router B.
    Reset
    Scoring Rule for:   correctness of response
    2 points for Option 2


    Assessment Item:
    Which two statements describe functions or characteristics of CDP? (Choose two.)

    It starts up automatically and allows the device to detect directly connected neighbor
    devices that use CDP.
    It operates at the network layer and allows two systems to learn about each other.
    It creates a topology map of the entire network.
    It allows systems to learn about each other even if different network layer protocols are
    configured.
    It forwards advertisements about routes for faster convergence.
    Reset
    Scoring Rule for:   correctness of response
    Option 1 and Option 4 are correct.


    Assessment Item:

    Refer to the exhibit. What two commands will change the next-hop address for the 10.0.0.0/8
    network from 172.16.40.2 to 192.168.1.2? (Choose two.)

    A(config)# no network 10.0.0.0 255.0.0.0 172.16.40.2
    A(config)# no ip address 10.0.0.1 255.0.0.0 172.16.40.2
    A(config)# no ip route 10.0.0.0 255.0.0.0 172.16.40.2
    A(config)# ip route 10.0.0.0 255.0.0.0 s0/0/0
    A(config)# ip route 10.0.0.0 255.0.0.0 192.168.1.2
    Reset    View Learner Response
    Scoring Rule for:   correctness of response
    Option 3 and Option 5 are correct.


    Assessment Item:

    Refer to the exhibit. What is the significance of the /8 in the route to the 10.0.0.0
    network?

    It indicates that there are 8 hops between this router and the 10.0.0.0 network.
    It represents the time, in milliseconds, it takes for a ping to reply when sent to the
    10.0.0.0 network.
    It indicates that there are 8 subnets in the destination network to which the router can
    forward packets.
    It indicates the number of consecutive bits, from the left, in the destination IP address
    of a packet that must match 10.0.0.0 to use that route.
    Reset
    Scoring Rule for:   correctness of response
    2 points for Option 4


    Assessment Item:

    Refer to the exhibit. A company network engineer is assigned to establish connectivity
    between the two Ethernet networks so that hosts on the 10.1.1.0/24 subnet can contact hosts
    on the 10.1.2.0/24 subnet. The engineer has been told to use only static routing for these
    company routers. Which set of commands will establish connectivity between the two Ethernet
    networks?

    R1(config)# ip route 10.1.2.0 255.255.255.0 192.168.0.1
    R2(config)# ip route 10.1.1.0 255.255.255.0 192.168.0.2
    R1(config)# ip route 10.1.2.0 255.255.255.0 192.168.0.2
    R2(config)# ip route 10.1.1.0 255.255.255.0 192.168.0.1
    R1(config)# ip route 10.1.1.0 255.255.255.0 192.168.0.2
    R2(config)# ip route 10.1.2.0 255.255.255.0 192.168.0.1
    R1(config)# ip route 10.1.1.0 255.255.255.0 192.168.0.1
    R2(config)# ip route 10.1.2.0 255.255.255.0 192.168.0.2
    R1(config)# ip route 0.0.0.0 0.0.0.0 10.1.2.1
    R2(config)# ip route 0.0.0.0 0.0.0.0 10.1.1.1
    Reset
    Scoring Rule for:   correctness of response
    2 points for Option 3




    Assessment Item:
    A network administrator enters the following command into Router1: ip route 192.168.0.0
    255.255.255.0 S0/1/0. Router1 then receives a packet that is destined for 192.168.0.22/24.
    After finding the recently configured static route in the routing table, what does Router1
    do next to process the packet?

    drops the packet because the destination host is not listed in the routing table
    looks up the MAC address of the S0/1/0 interface to determine the destination MAC address
    of the new frame
    performs a recursive lookup for the IP address of the S0/1/0 interface before forwarding
    the packet
    encapsulates the packet into a frame for the WAN link and forwards the packet out the
    S0/1/0 interface
    Reset
    Scoring Rule for:   correctness of response
    2 points for Option 4



    Assessment Item:
    A router has one static route configured to each destination network. Which two scenarios
    would require an administrator to alter the static routes that are configured on that
    router? (Choose two.)

    The destination network no longer exists.
    The destination network is moved to a different interface on the same router.
    The path between the source and destination is upgraded with a higher bandwidth link.
    The remote destination network interface has to be down for 15 minutes of maintenance.
    A topology change occurs where the existing next-hop address or exit interface is not
    accessible.
    Reset    View Learner Response
    Scoring Rule for:   correctness of response
    Option 1 and Option 5 are correct.


    Assessment Item:

    Refer to the exhibit. What two commands are required to provide connectivity between the
    192.168.1.0 and 10.0.0.0 networks without requiring recursive lookup? (Choose two.)

    A(config)# ip route 10.0.0.0 255.0.0.0 s 0/1/0
    A(config)# ip route 10.0.0.0 255.0.0.0 172.16.40.2
    A (config)# ip route 10.0.0.0 255.0.0.0 s 0/0/0
    B(config)# ip route 192.168.1.0 255.255.255.0 s 0/0/0
    B (config)# ip route 192.168.1.0 255.255.255.0 172.16.40.1
    B(config)# ip route 192.168.1.0 255.255.255.0 s 0/1/0
    Reset    View Learner Response
    Scoring Rule for:   correctness of response
    Option 1 and Option 4 are correct.

    Assessment Item:
    What two devices are responsible for converting the data from the WAN service provider into
    a form acceptable by the router? (Choose two).

    the serial port of the router
    a modem
    a switch
    the ethernet port of the router
    a CSU/DSU device
    a DTE device
    Reset    View Learner Response
    Scoring Rule for:   correctness of response
    Option 2 and Option 5 are correct.


    Assessment Item:
    Which piece of information is available from examining the output of the command show ip
    interface brief?

    Interface speed and duplex
    Interface MTU
    Errors
    Interface MAC address
    Interface IP address
    Reset
    Scoring Rule for:   correctness of response
    2 points for Option 5


    Assessment Item:

    Refer to the exhibit. Given the output in the exhibit, how would a clock rate be determined
    for this link?

    The rate would be negotiated by both routers.
    A rate would not be selected due to the DCE/DTE connection mismatch.
    The rate configured on the DTE determines the clock rate.
    The rate configured on the DCE determines the clock rate.
    Reset
    Scoring Rule for:   correctness of response
    2 points for Option 4


    Assessment Item:

    The routers in the diagram use the subnet assignments shown. What is the most efficient
    route summary that can be configured on Router3 to advertise the internal networks to the
    cloud?

    192.1.1.0/26 and 192.1.1.64/27
    192.1.1.128/25
    192.1.1.0/23 and 192.1.1.64/23
    192.1.1.0/24
    192.1.1.0/25
    192.1.1.0/24 and 192.1.1.64/24
    Reset
    Scoring Rule for:   correctness of response
    2 points for Option 5


    Assessment Item:
    What happens to a static route entry in a routing table when the outgoing interface is not
    available?

    The route is removed from the table.
    The router polls neighbors for a replacement route.
    The route remains in the table because it was defined as static.
    The router redirects the static route to compensate for the loss of the next hop device.
    Reset
    Scoring Rule for:   correctness of response
    2 points for Option 1


    Assessment Item:

    Refer to the exhibit. Which set of commands will configure static routes that will allow the
    WinterPark and the Altamonte routers to deliver packets from each LAN and direct all other
    traffic to the Internet?

    WinterPark(config)# ip route 0.0.0.0 0.0.0.0 192.168.146.1
    Altamonte(config)# ip route 10.0.234.0 255.255.255.0 192.168.146.2
    Altamonte(config)# ip route 0.0.0.0 0.0.0.0 s0/1
    WinterPark(config)# ip route 0.0.0.0 0.0.0.0 192.168.146.1
    Altamonte(config)# ip route 10.0.234.0 255.255.255.0 192.168.146.2
    Altamonte(config)# ip route 198.18.222.0 255.255.255.255 s0/1
    WinterPark(config)# ip route 172.191.67.0 255.255.255.0 192.168.146.1
    WinterPark(config)# ip route 0.0.0.0 0.0.0.0 192.168.146.1
    Altamonte(config)# ip route 10.0.234.0 255.255.255.0 192.168.146.2
    WinterPark(config)# ip route 172.191.67.0 255.255.255.0 192.168.146.1
    Altamonte(config)# ip route 10.0.234.0 255.255.255.0 192.168.146.2
    Altamonte(config)# ip route 0.0.0.0 0.0.0.0 s0/0
    Reset
    Scoring Rule for:   correctness of response
    2 points for Option 1


    Assessment Item:
    Why is it advisable to enter a next-hop IP address when creating a static route whose exit
    interface is an Ethernet network?

    Adding the next-hop address eliminates the need for the router to do any lookups in the
    routing table before forwarding a packet.
    In a multi-access network, the router cannot determine the next-hop MAC address for the
    Ethernet frame without a next-hop address.
    Using a next-hop address in a static route provides a route with a lower metric.
    In multi-access networks, using a next-hop address in a static route makes that route a
    candidate default route.
    Reset
    Scoring Rule for:   correctness of response
    2 points for Option 2


    Assessment Item:
    Which of the following are displayed by the Router# show cdp neighbors command? (Choose
    three.)

    load
    platform
    reliability
    holdtime
    local interface
    Reset
    Scoring Rule for:   correctness of response
    Option 2, Option 4, and Option 5 are correct.


    Assessment Item:

    Refer to the exhibit. Which static route should be configured on Router1 so that host A will
    be able to reach host B on the 172.16.0.0 network?

    ip route 192.168.0.0 172.16.0.0 255.255.0.0
    ip route 172.16.0.0 255.255.0.0 192.168.0.1
    ip route 172.16.0.0 255.255.0.0 S0/0/1
    ip route 172.16.0.0 255.255.0.0 S0/0/0
    Reset
    Scoring Rule for:   correctness of response
    2 points for Option 4


    Assessment Item:
    Hosts on two separate subnets cannot communicate. The network administrator suspects a
    missing route in one of the routing tables. Which three commands can be used to help
    troubleshoot Layer 3 connectivity issues? (Choose three.)

    ping
    show arp
    traceroute
    show ip route
    show controllers
    show cdp neighbor
    Reset
    Scoring Rule for:   correctness of response
    Option 1, Option 3, and Option 4 are correct.


    Assessment Item:
    A static route that points to the next hop IP will have what administrative distance and
    metric in the routing table?

    administrative distance of 0 and metric of 0
    administrative distance of 0 and metric of 1
    administrative distance of 1 and metric of 0
    administrative distance of 1 and metric of 1
    Reset
    Scoring Rule for:   correctness of response
    2 points for Option 3

    Assessment Item:

    Refer to the exhibit. How will packets destined to the 172.16.0.0 network be forwarded?

    Router1 will perform recursive lookup and packet will exit S0/0.
    Router1 will perform recursive lookup and packet will exit S0/1.
    There is no matching interface associated with network 172.16.0.0 so packets will be
    dropped.
    There is no matching interface associated with network 172.16.0.0 so packets will take
    gateway of last resort and exit out S0/2.
    Reset    View Learner Response
    Scoring Rule for:   correctness of response
    2 points for Option 1

    Assessment Item:
    Which address can be used to summarize networks 172.16.0.0/24 thru 172.16.7.0/24?

    172.16.0.0/21
    172.16.1.0/22
    172.16.0.0 255.255.255.248
    172.16.0.0 255.255.252.0
    Reset    View Learner Response
    Scoring Rule for:   correctness of response
    2 points for Option 1




    Assessment Item:
    The output of the Router# show interfaces serial 0/1 command displays the following:
    Serial0/1 is up, line protocol is down.
    What is the most likely cause for the line protocol being down?

    Serial0/1 is shutdown.
    There is no cable connecting the routers.
    The remote router is using serial 0/0.
    No clock rate has been set.
    Reset
    Scoring Rule for:   correctness of response
    2 points for Option 4

    您需要登录后才可以回帖 登录 | 立即注册

    本版积分规则

    手机版|小黑屋|Archiver|iOS开发笔记 ( 湘ICP备14010846号 )

    GMT+8, 2024-3-29 17:34 , Processed in 0.047121 second(s), 23 queries .

    Powered by Discuz! X3.4

    Copyright © 2001-2021, Tencent Cloud.

    快速回复 返回顶部 返回列表